AI Copilot

Live AI layout

/layout places, pours planes, drops vias and routes while you watch — and applies nothing until you say so.

/layout route

Who does what

The top lane is you; the bottom lane is WireFrame Copilot.

You
01

Get the board ready

OutlineLayers/layout

A board outline and the copper layer count — two is cheapest, four adds inner planes. Then type /layout.

05

Apply or discard

Apply/layout fix

Apply it to the board, discard it, or let /layout fix change what the failures call for. Ctrl+Z undoes one stage at a time.

06

Finish by hand

Critical netsDRCDFM

Route power, high-speed and RF paths yourself where they matter, then run DFM & DRC before you order.

WireFrame Copilot
02

Place

ConnectorsDecoupling

On a copy of the board: connectors at the edge facing out, each block round its busiest part, decoupling against its pins.

03

Planes, vias, route

PlanesViasRoute

Pours the planes the rules ask for, fans plane pads into their own rail, routes the rest, then stitches ground.

04

Measure what is left

UnroutedOverlapsRules

Whatever it could not finish is named and counted, never shipped as a violation. You watch every stage on the canvas.

A Raspberry Pi LED HAT laid out by the layout assistant, shown layer by layer

The layout assistant works on a copy of the board and streams every step onto the canvas: placement, planes, vias, routing and stitching. It measures what it could not do and why, and the board only changes when you apply the result.

What it does

Watch it work

Each step appears on the canvas as it happens.

Measured, not scored

Unrouted length, overlaps and dead copper are reported as numbers you can check.

On a copy

Your board is untouched until you apply.

Step by step

Run only placement, only routing, or the whole sequence.

Drawing of a placement head lowering a chip onto its footprint over a board whose left half is already routed and lit, its right half still footprints and dashed connections

Five stages, on a copy, while you watch

/layout works on a copy of the board and streams each stage to a live card in the chat: Place puts connectors at the edge and each block around its busiest part with decoupling against the pins it serves; Planes adds the pours the rules ask for; Vias fans out plane pads into their own rail's region; Route draws every net no plane carries; Stitch adds ground stitching and the edge via fence. The board only changes when you press Apply, and Ctrl+Z then takes it back one stage at a time.

Nothing forced, everything measured

A net that cannot be routed cleanly is named, never shipped with a violation. /layout fix runs the layout, reads every failure — unrouted connections and the circuit's own rules — changes what it calls for and runs again, without a model call. With a free-text request it can lay the board out several ways, compare them on parts placed, connections routed, vias, copper, overlaps and decoupling distance, say which the numbers favour, and ask which to apply.

The decisions that stay yours

The copper layer count sets the board's price, so the Copilot asks for it before the first layout and records the answer. It changes a net class only if you allowed rule changes, never below the fabricator's minimum and never below 0.10 mm track and space on one- and two-layer boards, and says which classes it changed. An applied layout is a starting point: power, high-speed, RF and sensitive analog paths still deserve your hand, and DFM & DRC the last word.

The details

StagesPlace · Planes · Vias · Route · Stitch
Runs/layout · /layout place,route · fresh · reseed · fix · apply · discard · rules · check
Model callsNone for the stages and /layout fix; a free-text request plans with the model
Board changesOnly on Apply; Ctrl+Z undoes one stage at a time
Rule changesOnly if allowed, within the fabricator's limits, never below 0.10 mm on 1–2 layers
NeedsA board outline, and the copper layer count decided

How to start

  1. Open a board with an outline.
  2. Type /layout, or /layout route for routing only.
  3. Watch, inspect the numbers, then apply or discard.

Questions

Will it overwrite routing I have done?

Not unless you ask: /layout fresh takes existing tracks up first and /layout reseed places every part again. Otherwise it works on a copy and you decide whether to apply.

Why does it ask for the layer count?

Two layers is the cheapest board and four adds inner ground and power planes. That is a cost decision, so it is yours, recorded once for the project.

Do I need a paid plan?

It comes with the Max and Pro plans, on the plan's monthly AI credit. The Free plan has the design tools and no AI Copilot.