Reference

Glossary

4 min read Updated Markdown
On this page

Short definitions of the terms used in this guide, each with the page where WireFrame works with it.

Design and schematic#

BOM (bill of materials)
The list of parts a board needs, one row per part number, with quantities and designators. WireFrame writes it with the fabrication outputs; the AI Copilot plans one from a requirement (Design Agent).
Designator (reference)
A part's name on the sheet and the board — R14, U1, J3. It links a symbol to its footprint and is how cross-probing finds a part in every view.
ERC (Electrical Rules Check)
Checks the schematic's connectivity: floating inputs, outputs driving each other, nets with one pin, duplicate designators. See ERC.
Footprint (land pattern)
The copper pads, silkscreen and courtyard a part is soldered to. See Footprint Libraries.
Hierarchical sheet
A sheet placed inside another as a block, with labels as its ports. See Wiring & Nets.
Net, net label, power symbol
A net is everything electrically joined; a label names one and joins every wire with the same name; a power symbol (GND, +3V3) is a label that is a supply. See Wiring & Nets.
Netlist
The list of nets and the pins on each — what the schematic means electrically, and what the board is built from.
Symbol
A part's drawing on the schematic, with its pins. See Symbol Libraries.

Board#

Board outline (Edge.Cuts)
The board's shape, with its cutouts. See Board Shape and Outline.
Clearance
The minimum distance between copper of different nets (and to holes and the board edge). Set per net class in Design Rules.
Courtyard
The area a part occupies on the board, used to keep parts apart.
Net class
A group of nets sharing rules — track width, clearance, via size, and for fast signals impedance, skew and length targets. See Design Rules.
Ratsnest
The thin lines showing connections not yet routed. They disappear as you route.
Stack-up
The order and thickness of a board's copper and dielectric layers. Impedance, delay and plane capacitance are computed from it. See High-Speed Workbench.
Via (through, blind/buried, micro)
A plated hole joining copper layers. A through via goes through the whole board; blind and buried vias span only some layers; a microvia joins neighbouring layers. See Routing.
Zone (copper pour, plane)
A filled area of copper on a net — a ground plane, a power island. See Zones & Planes.

Checks and manufacturing#

DRC (Design Rule Check)
Checks the board's copper against its rules: clearances, widths, unconnected nets. See DFM & DRC.
DFM (Design for Manufacturing)
Checks against what a board house can make: drill sizes, annular rings, copper to edge, mask slivers. See DFM & DRC.
Excellon (drill file)
The format drill files are written in — plated and non-plated holes separately.
Gerber (RS-274X, Gerber X2)
The format board houses take: one file per layer (copper, mask, paste, silkscreen, outline). X2 adds attributes saying what each file is. See Fabrication and Export.
IPC-2221
The IPC standard WireFrame uses for a track's current capacity at a given temperature rise.
IPC-D-356A
A netlist format the board house uses for bare-board electrical test.
Pick-and-place (centroid) file
Each part's position, rotation and side, for the assembly machine.

Signal and power integrity#

Characteristic impedance (Z0, Zdiff)
The impedance a signal sees along a track, set by its width, the dielectric and the plane under it. USB 2.0 wants 90 Ω differential; Ethernet 100 Ω. See High-Speed Workbench.
Common mode
The part of a differential signal that is the same on both halves. Skew creates it, and it is what radiates. See Simulation.
Crosstalk (NEXT, FEXT)
Signal coupled from one track to its neighbour — near-end and far-end. See Checks.
Differential pair
Two tracks carrying a signal and its inverse, routed together. See Length Tuning and Differential Pairs.
EMI / radiated emission
Energy a board radiates. Products must stay under limits such as CISPR 32 or FCC Part 15. See EMI.
Fly-by / tee topology
Ways to route one driver to several receivers — a chain past each (DDR3/DDR4 address and command) or a split into branches. See Simulation.
IR drop
The voltage lost in copper between a regulator and the chip it feeds (current × resistance), on the supply and on the return. See Power Analyzer.
Length matching / time matching
Making the nets of a bus arrive together — by length, or by delay when they run on layers of different speed. See Length Tuning.
Meander (accordion, trombone, sawtooth)
Bumps added to a track to make it longer. See Length Tuning.
PDN (power distribution network)
Everything between a regulator and a chip's supply pins — copper, planes, capacitors. Its impedance across frequency must stay under a target. See Power.
Return path
The way a signal's current comes back — in the plane right under the track, when there is one. A gap in that plane forces it around and causes noise and emission. See Checks.
S-parameters (Touchstone)
A measured or simulated description of a channel's transmission and reflection across frequency, in .sNp files. See Simulation.
Skew
The difference in arrival time between the two halves of a pair, or between nets of a bus.
Termination
A resistor (or network) that matches a line's impedance so its signal does not reflect.

Simulation#

SPICE (ngspice, Xyce, LTspice)
Circuit simulators. WireFrame has ngspice built in and can use Xyce or LTspice. See Simulation.
Transient, AC, DC sweep, operating point
The analyses SPICE runs: over time, over frequency, over a swept value, and at rest. See Running a Simulation.
Testbench
The sources, loads and measurements around a circuit under simulation, with pass/fail criteria. See Testbenches & Measurements.

Products of several boards#

Assembly (.asmxml)
The boards that make a product and the connections between them. See Multi-Board Products.
Board stack (tower)
Boards mounted above each other, each on a spacer. See Enclosure Fit.
HAT, cape, shield
An add-on board for a Raspberry Pi, a BeagleBone, an Arduino. See Multi-Board Products.