Design tool

High-speed routing & length tuning

Differential pairs routed as pairs, meanders to match a bus, and a live length gauge.

Length-matching meanders around the Ethernet PHY of the h730duino board

Buses such as RMII, SDMMC or DDR need traces of equal length — or equal delay — and a pair needs its two halves together. Declare pairs and length groups (or let WireFrame find them by net name), route both halves of a pair at once, add accordion, trombone or sawtooth meanders where a net is short, and watch the gauge reach the target.

What it does

Pairs routed as pairs

Start on a pad of a declared pair and both halves follow at the class's width and gap; a GND return via is dropped beside a pair's layer change.

Meanders

The Tune Length tool, or right-click › High-speed › Tune length: match the partner, the group or the class target, with height, pitch, side and corner style.

Length or time

Skew and group tolerances in mils or in picoseconds — a net that changes layer is matched by its real delay, not just its length.

Checked with evidence

The High-Speed Workbench computes skew, impedance, return path and crosstalk on the routed copper, each result with its method and source.

Three ways to say which nets go together

Pairs and length groups are rules saved with the board, and there are three ways to make them. WireFrame reads the net names — USB_D+/D-, ETH_TX_P/N, DDR_DQ0…, QSPI_IO0…, *_CLK — and proposes each with a target and a confidence for you to accept. You can add them by hand in Design Rules. Or select tracks on the canvas and right-click: declare a differential pair, add to a length group, or make a new group from the selection.

A gauge beside the cursor, in length and in time

While you route a net that belongs to a pair, a group or a class with a target, the readout shows the routed length against its target and the difference, and the delay so far in picoseconds from the board's stack-up. When a skew or group tolerance is set in time, "short" means short in time: the same length on an inner and an outer layer is not the same delay. Press 7 when the gauge says short and the missing length is added as meanders on the spot; one undo after the route takes both back.

Meanders that do not undo themselves

The Tune Length tool sets each bump's height from the cursor's distance and its side from which side you hover. From the right-click menu you choose the target — the partner, the group's longest net or the class target — with height, pitch and Square, 45° or Round corners, and the hint says how much was added and how much is still missing. Keep the legs at least three widths apart (pitch of four widths or more), or they couple and the signal takes the short way round.

The details

Declared fromNet names · Design Rules · right-click on the canvas
Pair routingBoth halves at the class's width and gap; GND return vias at a layer change
TolerancesIn length (mil, mm) or in time (ps)
Meander targetsMatch pair · match group · class target
CornersSquare · 45° chamfer · round
Checked byDRC clearance, Design Rules ▸ High-Speed, and the High-Speed Workbench

How to start

  1. Design Rules › High-Speed › Detected from net names: accept the pairs and groups that are right.
  2. Route a pair from one of its pads: both halves follow.
  3. Right-click a short net › High-speed › Tune length, or use the Tune Length tool, until the gauge reads the target.

Questions

Why match in time rather than in length?

A net that changes layer travels at a different speed on each. On a six-layer test board a DQ line on a stripline arrives 26 ps after its DQS on the microstrip at the same length — a DDR4 byte lane allows ±3.5 ps — so a plain length check passes a board that fails.

Where should a pair be tuned?

Keep the gap constant and tune the short half near where the mismatch starts, usually just after the bend that caused it. Skew corrected far from its cause still turns into common mode on the way, and common mode is what radiates.

Can I change the length-tuning key?

Yes — 7 is KiCad's key and the default; change it in Preferences ▸ Hotkeys.