PCB layout New
Length Tuning and Differential Pairs
On this page
Buses such as RMII, RGMII, SDMMC, QSPI or DDR need their traces to arrive together; a differential pair needs its two halves to stay together and equal. WireFrame keeps these as rules on the board — pairs, length groups and class targets — and gives you the tools to route and tune against them while you see the numbers.
Declare pairs and groups#
Three ways, all ending in the same rules (saved in the .pcbxml):
- From net names. Design Rules ▸ High-Speed ▸ Detected from net names (or Properties ▸ Board Settings ▸ High-speed ▸ High-speed nets) finds
USB_D+/D-,ETH_TX_P/N,DDR_DQ0…,QSPI_IO0…,*_CLKand more, each with a target and a confidence. Accept the ones that are right. The High-Speed Workbench does the same on its Start here page and goes further: whole interfaces (USB, Ethernet, DDR byte lanes, RGMII, QSPI, SD/eMMC) with their published rules. - By hand, in Design Rules. Add pair and Add group on the High-Speed page.
- From the canvas. Select tracks, right-click ▸ High-speed ▸ Pairs & groups: Declare as differential pair, Remove from its pair, Add to length group ▸ an existing group, or New group from selection.
A pair's width and gap, its skew limit and a group's tolerance live on net classes — in length, or in time (picoseconds) when the nets change layer. See Design Rules and the Workbench's Rules.
Route a pair as a pair#
With Properties ▸ Board Settings ▸ High-speed ▸ Pairs: Both halves on (the default), starting a route on a pad of a declared pair routes both halves together at the class's width and gap.
When the pair changes layer, Return vias: Add GND vias drops a ground via beside its two vias, so the return current changes reference plane at the same place as the signal. The High-Speed checks report a layer change without one.
The length gauge#
While you route a net that belongs to a pair, a length group or a class with a target length, the readout beside the cursor shows the routed length against its target — how long it is, how long it should be, and the difference — and the high-speed nets show markers in the layer list. In Properties, a selected track of such a net shows its measured length and its delta to the target.
The readout also gives the delay of the net as routed so far, in picoseconds, from the board's stack-up (the same model the impedance readout and the High-Speed checks use). When the pair's skew or the group's tolerance is set in time (ps), the skew is shown in ps too and "short" means short in time: the same length on an inner and an outer layer is not the same delay.
Tune while you route#
When the readout says the net is short, press 7 (KiCad's length-tuning key; change it in Preferences ▸ Hotkeys): meanders that make up what is missing are added to the net's copper at once — the same meanders the Tune Length tool would place — and the route goes on. They belong to the route: one Ctrl+Z after finishing takes the route and its meanders back.
Add meanders#
With the Tune Length tool#
- Pick Tune Length on the PCB toolbar.
- Hover a straight segment of a net that is short — short against its pair, its length group, or its class target.
- The distance of the cursor from the segment sets the bump height; the side of the segment it is on sets the side.
- Click to add. Esc leaves the tool.
From the right-click menu#
Select a track, right-click ▸ High-speed ▸ Tune length:
| Field | Meaning |
|---|---|
| Target | Match pair (the partner's length), Match group (the group's longest), or Class target — each with the length it means |
| Add (mil) | How much length to add (filled from the target) |
| Height (mil) | How tall each bump is |
| Pitch (mil) | Centre to centre of the two legs of a bump. Keep legs at least 3 widths apart (pitch ≥ 4 × width) or they couple and the signal takes the short way |
| Left / Right | Which side of the track the bumps go |
| Corners | Square, Chamfer 45° or Round |
Press Add meander. The hint says how much was added in how many bumps — and how much is still missing if the segment was too short ("raise the height", or pick a longer straight segment).
The default corner style for every way of tuning is Properties ▸ Board Settings ▸ High-speed ▸ Meanders.
Where to tune a pair
Keep the gap constant and tune the short half near where the mismatch starts — usually right after the bend that made it. Skew that is corrected far from its cause still turns into common mode on the way, and common mode is what radiates.
Check it#
- DRC checks clearance around meanders like any other copper.
- Design Rules ▸ High-Speed shows each pair's skew and each group's length spread.
- The High-Speed Workbench ▸ Checks computes skew and matching in time as well as in length, impedance per layer, return path and crosstalk — see Checks.