Start here
Learning paths
On this page
Not sure what to read first? Choose the path that matches you. Each one lists the pages in order, how long each takes, and what you will be able to do at the end. Tick the boxes as you go — they are just for you.
New to PCB design#
You have never drawn a schematic or a board, or it has been a while. About 1 hour.
- Install WireFrame 10 min — download, install, first launch.
- Getting started 10 min — create a project, add a schematic and a PCB.
- The user interface 5 min — what every panel is for.
- Placing components and Wiring & nets 10 min
- Tutorial: An LED Chaser Board 60 min — the whole flow on one 25-part board.
- ERC and DFM & DRC 5 min — read the checks before you trust a board.
At the end you can
draw a small circuit, check it, turn it into a PCB, route it, and export files a manufacturer accepts.
Coming from KiCad or Altium#
You know EDA; you want your work across and the differences. About 30 minutes.
- Projects & files 5 min —
.prjxml,.schxml,.pcbxml, and importing a KiCad project. - Import & export 5 min — open Altium projects; write KiCad, Altium or EasyEDA projects back out.
- Library import & management 10 min — KiCad folders, Altium
.SchLib/.PcbLib/.IntLib. - Keyboard shortcuts 5 min — the keys that differ from what your hands expect.
- Selection, context menus & popups 5 min
- Design rules & net classes 5 min
At the end you can
open an existing KiCad design in WireFrame, reuse your libraries, and work at your usual speed.
Design with AI#
You want the Copilot to draft a circuit and you want to know how to review it. About 45 minutes.
- AI overview 10 min — settings, sessions, what the Copilot can and cannot change.
- Tutorial: AI-Assisted Design 20 min — an NE555 blinker from a one-line request.
- AI Design Agent 5 min — the Component Review tabs, card by card.
- Fix or Create a Component 5 min — when a part is not in your library.
- Review & simulation guide 5 min — what to verify before you apply.
At the end you can
turn a written requirement into a reviewed BOM and schematic, and tell a sound proposal from a risky one.
High-speed and power#
Your board has USB, Ethernet, DDR, PCIe or a hungry processor, and you want proof the copper is right. About 50 minutes.
- Length tuning & differential pairs 10 min — route pairs as pairs, match a bus.
- High-Speed Workbench 10 min — stack-up, rules, the six steps.
- Checks & interfaces 10 min — read a result's evidence; check USB or Ethernet as a whole.
- Simulation, power & EMI 10 min — a pair in time, a rail's impedance, the nets that radiate.
- Power Analyzer 10 min — the voltage each chip really sees.
At the end you can
tell which fast signals and rails are right, which are not and why — and fix them with changes you previewed and approved.
Ready for manufacturing#
The design is done; you need a clean, consistent release. About 30 minutes.
- Design rules & net classes 5 min
- Zones & planes 5 min
- DFM & DRC check 10 min — resolve every blocking error, justify every warning.
- Fabrication & export 10 min — Gerber, drill, BOM and their inventory.
At the end you can
hand a manufacturer a package where every file belongs to the same saved board revision.
Simulate a circuit#
You want to know a circuit works before it is built. About 30 minutes.
- Simulation workbench 5 min
- Engines & SPICE models 10 min — every part needs a model.
- Running a simulation 5 min — blocks, preflight, run.
- Testbenches & measurements 5 min
- Waveform viewer 5 min — signals and A/B cursors.
At the end you can
run a simulation on a block of your schematic and measure the result instead of eyeballing it.
Done with a path? The FAQ & Troubleshooting page collects the questions people ask next.