Schematic New
Design Blocks and Channel Reuse
On this page
Design blocks#
A design block is a piece of circuit kept to be placed again: a regulator with its capacitors, an input filter, a connector with its protection. WireFrame keeps blocks in KiCad's own format (KiCad 9 and 10), so a block made in WireFrame opens in KiCad and a block from KiCad places in WireFrame:
MyBlocks.kicad_blocks/ a library is a folder
ldo_3v3.kicad_block/ a block is a folder in it
ldo_3v3.kicad_sch its circuit, symbols included
ldo_3v3.json description, keywords, fields
ldo_3v3.kicad_pcb its layout (KiCad 10), when saved with one
Tools ▸ Design Blocks opens the block window: the libraries on the left, the block picked on the right with a preview of its circuit.
Libraries#
| Library | Where |
|---|---|
| WireFrame | Your own blocks, in ~/.wireframe/design_blocks/. Always there, always writable |
| The project's | Every library in the project's design-block-lib-table (${KIPRJMOD} is the project folder) |
| KiCad's | Every library in KiCad's own design-block-lib-table, when KiCad is installed |
Save a block#
- Select what the block holds on a sheet — parts, wires, labels, power symbols, notes. Wires between two selected parts come with them.
- Tools ▸ Save Selection as Design Block… (or the Save selection as a block card in the window).
- Pick the library, give it a name, a description and keywords, and Save block.
A part keeps the footprint it names (Resistor_SMD:R_0603_1608Metric). When the project's board is open and the selected parts are placed on it, the block also keeps their layout: the footprints and the tracks and vias between them.
Place a block#
Pick it and Place on sheet. The block lands in the middle of the view — or, when that would cover what is already drawn, in the free space to the right — and stays selected, so you drag it where it goes. It is one undo step.
- Its parts take the next free designators of the whole project (
R1,R2of the block becomeR14,R15), units of one part keep one designator, unnumberedR?are numbered. Tick Keep the block's designators to keep the ones that are free. - Labels and power symbols come as they are: a label named
VINjoins theVINalready in the design. - The block moves by whole 50 mil (1.27 mm) steps, so its pins stay on the grid.
Apply a block's layout#
For a block saved with its layout: after Update PCB from schematic, make the board the active view and press Apply its layout to the board. WireFrame finds every place the block was placed on the project's sheets (its parts still drawn as placed), keeps the largest part of each where you put it on the board, places the others around it as in the block — turned with it — and lays the block's tracks and vias on that placement's nets. The routing of nets that only that placement uses is replaced; Ctrl+Z undoes the copper, then the placement.
Repeat a channel's layout#
A design with several identical channels (an 8-channel ADC front end, a multi-output driver) usually draws each channel as a copy of one sheet. Tools ▸ Repeat Channel Layout finds them: sheets with the same parts at the same places are channels.
- Lay out one channel on the board — placement and routing.
- Open Tools ▸ Repeat Channel Layout, pick that channel as the Reference, and tick the channels to lay out like it.
- Repeat layout.
Each channel keeps its own copy of the reference's largest part where you placed it; the other parts are placed around it as the reference's are, turned with it. With Copy routing on, the reference's tracks and vias are laid on each channel's own nets; a net channels share (ground, a supply) is copied only where it runs among the channel's parts, and never twice. With Replace routing on, a channel's own earlier routing is taken up first — shared nets never are.
Parts are matched by where they are on the sheet and what they are, not by designator, so channels numbered R101… and R201… match. A part moved on one sheet makes that sheet a different circuit: it is no longer a channel.
See also#
- Placing components
- Footprints and placement
- Import & export — KiCad round trips